How To Fill Gap Between Baseboard And Floor? Best Guide – 101

How To Fill Gap Between Baseboard And Floor

Would you like to know the right method for, how to fill gap between baseboard and floor? Well, that is the exact topic that we discuss today and find answers to.

It is no doubt that the Baseboard is so thin than the surface of a typical Door. In fact, the Baseboard is a light wooden board that runs along the bottom of an interior wall. It yet confuses the people on how to fill gap between Baseboard and Floor in today’s world despite the world turning more and more modern. Read the following to learn how you can fill the Baseboard and floor gap correctly!        

What Is The Essential Purpose Of A Baseboard?

Before we explore the answer to “how to fill gap between baseboard and floor,” let’s see the real purpose of a baseboard in the first place.

It is not new that the Baseboard helps you protect and cover the joint between the base wall surface and the floor, and the Baseboard covers the empty uneven edge of the bed next to a wall.

People consider that Baseboard only serves as decor and believe that it is an additional expense to have Baseboard. Thus, they don’t regard the consequences and conclude not to have Baseboard in contemporary. Nevertheless, the essential purpose of having a Baseboard is to prevent insects from getting into your place through the uneven edges of the floor and wall and not to demonstrate an odd appearance. 

Is It Required To Have A Carpenter Fix The Baseboard, Or Can I Fix It On My Own?     

Although the ambition of writing this article is to search for answers to How To Fill Gap Between Baseboard And Floor, there are certain things you need to know additionally.

This particular process depends on your confidence and skill. Frankly, you don’t require a meson or carpenter to fix the Baseboard if you’re skilled enough. If you don’t find setting the Baseboard easy, you can call out a carpenter, which is not a concern. But still, you should make sure that you set the Baseboard in the right place, and right angle, and fill the gap between the Baseboard and floor.

How do I place the Baseboard perfectly?

You will only have to read the next phase of the article, which is How To Fill Gap Between Baseboard And Floor if you don’t place the baseboard perfectly. So, here is the process of that. 

  • Firstly, you should decide the size of the Baseboard that you would prefer. Generally, most Baseboards run between 3 ¼ and 5 ¼ inches, and they are 5/8 inches thick and come in 16-foot strips. If you have chosen a specific type of Baseboard trim, you will have to choose a style that suits both. 
  • Secondly, establish the height of the Baseboard. For this process you need to set a 4-foot level on the floor to check whether the floor is levelled. Or else, you have to move the level across the floor to find its lowest point. When you find it, mark it or nail a scrap of Baseboard t the wall. 
  • Next, make horizontal marks on every foot at the same level on the wall. Then find out where the top edge of all the baseboards should land when installed. Starting from an inside corner, hold the board tight against the wall, level it, tack it on the exact place, and nail it. Set the compass ends to transit the vertical distance of the board’s top corners. Hold the pencil on the Baseboard and the point against the floor without altering the spread of the compass’s legs for a tight fit. Skate the compass along the floor over the Baseboard’s length, preserving the ends aligned vertically. With a 2- to a 5-degree angle, carve alongside the scribe stripe so the face of the cut will be on the flank toward the wall. Shorten the bevelled edge down to the line with a block plane. When the scribed Baseboard is put back on the wall, its edges should line up with the ends snapped earlier. 
  • Next, you have to set the scribed Baseboard in place. Then, hammer two nails through the board at each stud location, at a slight downward angle, near its top and bottom edges. Use a nail to avoid marking the wood and set to drive the heads just below the wood surface. 
  • Find the outside corner joints, fit one end of the board against the inside corner, and by the other end, you have to draw a perpendicular line up the back of the board, using the edge of the outside corner to guide the pencil. Then point out the top of the board to indicate the direction of the Mitre. Extract the marked board and place the one that will make up the Mitre’s other half against the adjoining wall. Mark the same way. 
  • Place a compound mitre noticed to 45 degrees and cut each Mitre just exceeding the line. In this form, you can fine-tune the joint. Place both panels back against the wall and study the joint. If it doesn’t exist tight on the side and top, go back to the saw or pick up a block plane and trim the wood until it is. 
  • It would help to make sure an outside mitre joint stays tight and connect the two halves with glue and Number 10 compressed-wood biscuits. Then, hold the two boards tightly against the outside corner and, by using a pencil, mark two places across the joint. The marks should be centred on each other and from the board’s edges. Then remove the boards, set the biscuit joiner perpendicular to the cut face, and accommodate the depth of its fence so the cut will be nearer to the backside of the boards. Align the tool’s centerline with a mark and plunge-cut a slot into the face of the cut. Do the same thing at the next point. 
  • Subsequently, squeeze some strong glue into both places and over the face of each half of the mitre cut. Then slip a biscuit into each space on one board and bring the two boards together. Position the boards back on the wall and drive two nails into the wall on each side of the Mitre. Between these nails, drive a nail through the joint and into the end grain of the opposite piece. Tap nail heads below the wood surface with a nail set. Where two boards meet on a straight run, construct a scarf joint by mitring the ends in opposing directions at a point where there’s a stud. Glue and overlap the mitres and nail through the piece covering the joint but not through the joint itself and into the stud. Simply butt the baseboard ends together for inside corners, then nail them to the wall. 
  • With the use of a cap moulding, position it on the base to check if the back of the moulding fits against the wall. Restrain it at each stud with a nail driven at a slight downward angle through the thicker parts of the moulding. If there are gaps behind the moulding and no stud to nail into, squeeze a drip of construction glue on the back of the moulding at those fixes and nail the moulding to the studs. Then nail the moulding to the wall between the studs to hold it until the glue sets.

HERE Are Exact Rubberwood Furniture Disadvantages. 

How To Fill Gap Between Baseboard and Floor?

Let’s see how to fill gap between baseboard and floor. Due to the imperfection of installing the Baseboard, there can be gaps between the Baseboard and floor. The best and most convenient way to fill the Baseboard and the floor gap is by the usage of a Caulk.

When the gap is 1/4-inch or even more petite, you can quickly fill the space with caulk. It would help if you had a caulk gun that works properly to do this particular job. One tip is as follows; cut the tip of the tube at an angle because it will aid in the distribution process.

When the caulk dries, it causes it to shrink because the water gets evaporated. It is also recommended to fill gaps with foam before adding caulk initially. Examine and take time to fill the space out evenly so caulk does not overflow in any specific area.

Even though adding caulk is time-consuming, it eventually helps the Baseboards to stay rampant with the wall. When you choose caulk for an undertaking like this, you must make sure it is painting caulk. By painting caulk, it means caulk that is labelled or marked that paint can be applied. 

So, we hope now you know how to fit the baseboard perfectly and answer the question of How To fill Gap between Baseboard and Floor if needed. 


Please enter your comment!
Please enter your name here