When you conduct house repairs or adjustments, you may wind up having holes in the ceiling when light fixtures have been removed or re-positioned. A hole in the ceiling isn’t something you want to see every day, and you shouldn’t have to replace the entire ceiling to fix a little hole. So you’re considering how to patch a hole in the ceiling? In this post, we will teach you how to repair a hole in the ceiling since it is no longer visible and will not be a problem in the future.
Hole In A Ceiling
A scuttle attic is an attic chamber that a small roof hole may access. A hatch is a term for the aperture and the panels covering it.
How Big Of A Hole Can The Patch Fix In The Ceiling?
Mending a large hole in drywall—anything more than six inches—is not the same as repairing a tiny hole in drywall. Small holes may get repaired using drywall tape or a self-adhesive drywall patch, while bigger holes require a more firm substance to span the wider opening.
How To Patch A Hole In The Ceiling? – Larger Than 12 Inches Wide
To begin, resist the urge to seal the hole with such a scrap of drywall or plaster ceiling board. When you try to fix a hole in this manner, the only thing holding the plug in place is a bit of drywalling plaster. There have been a few occasions where the plaster has broken, and the plug has come loose, requiring you to repeat the procedure.
The most acceptable approach to mending a hole in a ceiling without replacing a ceiling panel or even the entire sealant get given below. All of the materials may get purchased at your local construction supply store.
So you stepped through to the ceiling after missing the rafter, don’t hire a handyperson to mend the enormous hole. You may repair yourself and save a lot of money on labor fees. All you need to repair the ceiling is a sheet of drywall and a few tools from your local hardware shop or home center. After mending the hole, apply a whole can of spray paint to complete the job like an expert.
- Examine the area around the opening for electrical wiring in the attic. Move cables away from the hole or hire a company, but don’t cut into the ceiling if wires might get damaged.
- Locate two joist beams, one on each side, near the hole. Make two tiny holes through the ceiling using a cordless drill and a long bit to indicate the placement of the two beams.
- Return to the ceiling and cut and replace the damaged drywall using a drywall knife. Begin at one spot and cut a square that extends to the opposing mark. Remove the drywall first from the ceiling to expose the beams.
- Measure the drywall piece that got removed from the ceiling. Cut a replacement piece from a fresh sheet of drywall slightly smaller than the hole.
- Insert the replacement drywall into the hole. To avoid cracking, place the nails about 1 inch from the drywall’s edge. Using the drill, attach the drywall to the joist beams.
- To use a drywall taping knife, apply a thin coating of joint drywall compound to the seam around the edge of the new piece. Mesh drywall tape should be cut to suit the size of the seams and pressed into the wet compound. Allow drying thoroughly after applying a thin mix coating, so over the tape and insert it into the seam.
- Then use a fine-grit sanding block, and smooth the mended seams to the ceiling. More compound should get applied to open seams, allowed to cure, and then sanded again. Using a clean cloth, wipe away the sanding dust.
- Using a texture spray can apply ceiling paint to the mended area. Apply the texture according to the manufacturer’s recommendations and let it dry thoroughly.
- Using a paint roller, put primer on the mended area. Let the primer dry completely before applying two layers of ceiling paint.
How to Insulate a Garage Ceiling Rafters? Read HERE.
How To Patch A Hole In The Ceiling? – Larger Than 1 Inch, but Less Than 12 Inches Wide
- With a putty knife, scrape off the ceiling texturing 2 inches beyond the hole’s perimeter.
- Using a putty knife, apply drywall cement around the hole. Using scissors, cut a piece of plastic mesh repairing material to cover the hole, sizing the patch to extend 1 inch beyond the hole. Cover the hole completely with the patch and firmly push the edges into the moist compound. Apply a thin compound coating to the whole area using the putty knife. Let the patch completely dry.
- Then use a fine-grit sanding block, and smooth the mended area to the surface. Apply another coat of compound to any recessed areas, let dry, then sand the area again. Using a clean cloth, wipe away the sanding dust.
- Using a texture spray can apply ceiling texture towards the mended area. Apply the surface according to the manufacturer’s recommendations and let it dry thoroughly.
- Using a spray can put primer on the mended area. Let the primer dry completely before applying two applications of ceiling paint.
What Color To Paint House With Green Roof? Read HERE.
How To Patch A Hole In The Ceiling? – Less Than 1 Inch Wide
- Fill that void with vinyl spackling using a putty knife. Remove any excess spackling with a clean cloth. Allow the spackling to dry thoroughly.
- Sand the patched hole to the ceiling’s surface using a fine-grit sanding block. Wipe the sanding dust away with a clean cloth.
- Using a tiny paintbrush, apply ceiling color to the mended hole.
How To Patch A Hole In The Ceiling – Final Thought
That’s all our guide on How To Patch A Hole In The Ceiling! It will cost you nothing to do, only use a tiny amount of compound, some tape, and a brush destined for the garbage.
